Oscillocope
We are engaged in offering Oscilloscopes to our clients. Oscillocope 6020 is a 20MHz Dual Channel Oscialloscope that is ideal for professionals as well as students undergoing technical studies. it is a ruged, lightweiht instrument that features a bright, sharply defined trace on an 80 x 100 mm cathode ray tube. The low noise vertical system supplies calibrated deflection factors from 5m V to 10V per division at full bandwidth. Stable triggering is achieved over the full bandwidth of the vertical system. The flexibility and high sensitivity of the rigger system provides a range of conveniences such as automatic trigger mode, normal trigger mode, independent selection of V field triggerin and single sweep triggering. The internal triger signal is AC coupled, An external triggering signal or an external Z-axis modulation signal can be appied via a front panel or rear panel connector and the source selector switches. The horizontal system provides calibrated sweep speeds from 0.2S to 0.1uS per division. For greater measurement accuracy a "X 5" - magnifiercircuit extends the maximum sweep to 20nS per division. Feel free to contact us.
Special Features
Synchronization of the signals from the two channels can be identified by a red LED, marked as "TRIG'D", present on the right hand side top on the front panel. Synchronization can be achieved even if the waveform inputs in both the channels are different in amplitude, frequency and shape X & Y Channel (V/mV) amplitude calibration facility is provided. Variable sweep facility is also available. Upto 400V peak Voltage input in both the channels are possible.
Bandwidth
|
DC - 20 MHz
|
Deflection FActor
|
5 mV / Div ~ 10V / Div. Mag. X5
|
Sweep Rate
|
0.2S ~ 0.1uS / Div. Mag. X5
|
Trigger Synchroniztion
|
Int., Alt, line, Ext.
|
Sweep Mode
|
Auto, Trigger, Single Time
|
Vertcal Deflection System
Deflection Factor
|
5mV / Div. to 10V / in a
1-2-5 sequence of 11 steps
|
Accuracy
|
+- 5%
|
Variable Control Range
|
Continuously variable and
uncalibrated between step
setting. Increase deflection
factor by at least 2.5 to 1
|
Band widht
|
20 MHz
|
Rise Time
|
17.5nS or less
|
AC Coupled Cut Off Frequency
|
10 Hz or less
|
Common Mode Rejection Ratio
|
At least 10 to 1 at 20 MHz
|
Magnifier
|
XP, Provides 1 mV/Div
|
Mode
|
CH1, CH2, Alt, Chop,
Add,, Inv CH2, X-Y
|
Input Characteristics
|
Direct Input
|
Via. 10: 1 probe
|
Resistance
|
1 M © +- 2%
|
10 M © +- 5%
|
Capacitance
|
30 pF +- 5pF
|
20 pF +- 5pF |
Max. Safe Input Voltage
(DC or AC Coupled)
|
400 V (DC + AC) Peak
|
Channel Isolation
|
Greater than 10 : 1 @ 10 MHz
|
Invert Mode
|
In channel 2 only
|
Horizontal Deflection System
Sweep Rate
|
0.2 S / Div to 0.1 µS/Div in a
1-2-5 sequence of 20 Steps
Magnification extends
maximum possible usable
sweep speed to 20nS/Div
|
Accuracy
|
+- 5% Approx.
|
Variable Control
|
> 2.5 : 1
|
Sweep Linearity
|
+- 10%
|
Trigger System
Trigger senstivty
|
(For Auto & Norm. Mode)
|
Internal Signal
|
0.1 Div.
|
Exernal
|
0.2 VP-p
|
TV Field Mode
|
(Composite Sync.)
|
Internal
|
2 DIV
|
External
|
0.3 Vp-p
|
X-Y Operation
Deflection Factor
|
5m V/div ~ 10V/Div.
|
Bandwidth
|
DV: 0 ~ 1 MHz
|
AC
|
10 Hz ~ 1 MHz
|
Accuracy
|
+- 5%
|
Phase Difference
|
<3o from DC to 50 KHz
|
Z Modulation
Sensitivity
|
5V causes noticeable
modulation, Positive going
input decreases intensity
|
Usable Frequency Range
|
DC ~ 1 MHz
|
Max. Safe Input Voltage
|
50V (DC + AC) Peak
|
Input Resistance
|
10k © |
Proble Adjustment Signal Output
Voltage into 1 M © Load
|
0.5 V +- 2%
|
Repetition Rate
|
1 KHz +- 2%
|
Wave form
|
Square Wave
|
Component Tester
|
16v P-P (Approx.)
|
Cathode Ray Tube
Display Area
|
8 Div x 10 Div (1 Div = 1 cm)
|
Nomnal Acceleration Voltage
|
2 kv
|
Trace Rotation
|
Provded
|
Power Requirement
Lne Volage Range
|
230 V +- 10%
|
Line Freqency
|
50 Hz +- 2 Hz
|
Max. Power Consumption
|
40W approx.
|
General Characterisitcs
Weight
|
7.2 kgs (approx.)
|
Dimensions
|
320 mm (L) x 124 mm (W) x 380 mm (D)
|
Operation Temperature
|
0oC to 40oC |
Relative Humidity
|
90% (40oC) |
Accessories
Operation Manual
|
Power Chord; Dust Cover, BNC to
Crocodile Probes
|
Optional
|
1 : 1 & 10 : 1 probes
|
|
